We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

How to Set Up Mapex Double Bass Pedal: A Step-by-Step Guide

Learn how to set up Mapex double bass pedal step by step, from positioning and footboard height to spring tension and beater alignment for a smooth, even feel.

Updated November 2026

Setting up a Mapex double bass pedal comes down to four things: positioning the footboards, matching the footboard height, adjusting spring tension, and aligning the beaters. Work through them in that order and you will have two pedals that feel consistent, respond quickly, and sit comfortably under your feet. The whole process takes about 20 to 30 minutes once you know what to look for.

Before You Start

Gather a few basic tools so you are not improvising mid-session. Most adjustments on Mapex pedals use a hex key or a standard screwdriver, depending on the model. Check your owner’s manual for the exact fasteners, since Mapex designs vary across their lines.

Shopping for one? See our guide: 6 Best Electronic Drum Set Double Bass Pedals (2026): Our Picks.

  1. A hex key set (metric)
  2. A Phillips screwdriver
  3. A tape measure or ruler
  4. A practice pad or a sturdy surface to test on
  5. Your drum throne, adjusted to your usual height

Step 1: Position the Pedals on the Kick Drum Hoop

Mount the pedal so the footboards line up with your natural leg angle. Clamp the baseplate to the bass drum hoop, then slide the pedals left or right until the beater sits near the center of the drumhead. Tighten the clamp only after you are satisfied, because small shifts add up fast.

Most drummers find the sweet spot when the beater strikes the head about two-thirds of the way from the hoop toward the center, though this varies with your playing style.

Step 2: Set Footboard Height and Angle

Sit at your playing position with your feet on the footboards. Your heel should rest comfortably, and your ankle should sit at roughly a 90-degree angle when the pedal is at rest. If your heel floats too high, raise the footboard. If your foot feels cramped, lower it.

Keep both footboards at matching heights. Mismatched boards lead to uneven attacks, so measure each one from the floor with a tape measure and adjust until they are level.

Adjusting the Footboard Angle

Many Mapex pedals let you change the angle of the footboard relative to the pedal body. A slightly forward angle suits heel-up playing, while a flatter setting works better for heel-down technique. Try a few positions with light strokes before you lock anything down.

Step 3: Adjust Spring Tension and Beater Alignment

Spring tension controls how quickly the beater returns after each stroke. Start with the tension at a medium setting, play a few steady strokes, and then increase or decrease it in small increments. Too much tension tires your foot and slows rebound. Too little tension makes the beater bounce back unevenly.

Next, check beater alignment. The beater should strike the center of the head squarely, not at an angle. If it hits the edge or drifts sideways, loosen the beater mount and rotate it until the contact surface lies flat against the drumhead. Tighten the mount once it is centered.

Step 4: Test and Fine-Tune

Play at several dynamic levels, from soft single strokes to fast doubles. Listen for uneven volume between the two pedals and feel for any hitch in the return. Make one small adjustment at a time and retest, because changing tension and alignment together makes it hard to tell which change helped.

Checklist

  • Baseplate clamp tight and centered on the hoop
  • Beater striking the head squarely, about two-thirds toward center
  • Footboards level with matching heights
  • Spring tension set for smooth, even rebound
  • Both pedals tested at soft and fast tempos

Common Mistakes

  • Tightening the clamp before checking the beater position
  • Setting footboards at different heights
  • Cranking spring tension to maximum for speed
  • Skipping a retest after each small adjustment
  • Ignoring your throne height, which changes your leg angle

A stable practice pad helps you test pedal feel without the noise of a full kit. View on Amazon

A metric hex key set covers most Mapex adjustment points and keeps your tools in one place. View on Amazon

FAQ

How long does it take to set up a Mapex double bass pedal?

Most drummers finish in 20 to 30 minutes if they follow the steps in order. Expect longer the first time while you learn how each adjustment affects the feel.

Should both footboards be exactly the same height?

Yes, matching heights help both pedals produce even attacks. Measure each board from the floor and adjust until they line up.

Can I use a Mapex double bass pedal with a single kick drum?

Yes, a double pedal works on a single bass drum. You can play with one pedal or both, depending on the part you are playing.

Conclusion

A well-set Mapex double bass pedal feels balanced, responds evenly, and stays out of your way. Position the pedals carefully, match footboard heights, dial in spring tension, and align the beaters. For more detailed guidance on related setups, see How to Set Up Double Bass Pedal: A Step-by-Step Guide for Beginners and How to Adjust a Double Bass Pedal: A Step-by-Step Guide for Drummers.

Audrey Hayes

About Audrey Hayes

Audrey Hayes is part of our editorial team and reviews and edits our drums guides, checking product details against manufacturer specifications and owner feedback.

About the author

Audrey Hayes
Audrey Hayes

Audrey Hayes writes reviews and buying guides for Drum Path.