How to Make Your Own Double Bass Pedal: A Step-by-Step Guide
Learn how to make your own double bass pedal, from choosing a base and linkage to building the footboard, beater and spring tension for a reliable, playable res
Updated November 2026
Building your own double bass pedal is a realistic project for a handy drummer with basic metalworking tools. In this guide, you will learn how to plan the layout, build a working linkage, and set the spring tension so the pedal feels consistent from stroke to stroke. The finished pedal will not match a commercial unit in finish, but it can play well if the geometry and hardware are right.
Plan the Design Before You Cut Anything
Start with a clear layout. A double bass pedal is really two single pedals joined by a shared platform and a linkage, so you need to decide how the two beaters will sit relative to each other. Most builders place the beaters about 4 to 5 inches apart at the footboard, which matches the spacing many drummers find comfortable for heel-up and heel-down work.
Shopping for one? See our guide: 5 Best Electronic Drum Double Bass Pedal Options for Practice and Gigging (2026).
Sketch the footboard, the hinge point, the chain or strap path, and the beater pivot. Measure your own foot and the distance from your seat to the bass drum batter head before you commit to dimensions.
Build the Base, Footboard and Linkage
Materials and Tools
- Steel or aluminum plate for the base, roughly 1/4 inch thick
- Flat bar or angle stock for the footboard and beater arms
- Hardened steel or nylon bushings for the pivots
- Chain or cable with a sprocket or pulley, plus a tensioning spring
- Drill, taps, files, a hacksaw or band saw, and a square
- A felt or rubber beater head and a bolt-on beater shaft
Assemble the Frame
Drill the pivot holes with the bores square to the plate. A misaligned pivot will bind, and binding is the most common cause of a pedal that feels sticky or uneven. Use bushings in every pivot point so the joints move freely without play.
Set Up the Drive Linkage
Connect the footboard to the beater through a chain, strap or rod. Keep the linkage short and rigid. Each extra joint adds slop, so aim for the fewest moving parts that still give the throw you want.
Set the Spring Tension and Beater Stroke
Tension controls how quickly the beater returns and how much pedal force you need. Start with a moderate spring load, then adjust in small increments. Many drummers prefer a beater stroke of roughly 2 to 3 inches measured at the beater head, since a longer throw can feel slow and a shorter one can limit volume.
Test the pedal with a slow rebound check. The beater should return cleanly to a rest position about a quarter inch from the head, without bouncing back into it.
Common Mistakes
- Skipping bushings, which leads to play and sticky movement
- Making the footboard too small or too narrow for a comfortable heel position
- Over-tightening the spring so the pedal fights you on every stroke
- Leaving the beater angle unchecked, which causes uneven contact with the head
- Assembling the frame without checking squareness first
Recommended gear
A solid tool set makes the build much more accurate. A drill press with a set of quality bits helps keep pivot holes square, which matters more than any other step. View on Amazon
A set of hardened steel pivot bushings simplifies the joints and reduces friction. View on Amazon
A replacement beater with an interchangeable head lets you test different striking surfaces without rebuilding the whole pedal. View on Amazon
FAQ
Is it safe to build a pedal at home?
Yes, if you use proper eye protection and secure your workpieces before cutting or drilling. Metal edges can be sharp, so deburr every cut. If you are unsure about metalworking, consult an experienced machinist or fabricator.
How long does a homemade pedal take to build?
Expect a full weekend or more for a first build, since you will likely need to fit and adjust the linkage several times. Planning and careful measurement save significant rework.
Can a homemade pedal replace a commercial one for gigging?
It can work well for practice and light use, but a commercial pedal is usually tested for durability over repeated heavy use. Many players keep a proven pedal for live shows.
Conclusion
A homemade double bass pedal rewards careful planning, square pivots and patient spring tuning. Focus on the linkage and tension, and you can end up with a pedal that feels responsive and reliable. Once it is built, test it at several tensions before settling on your final setup.
Related reading
- How to Set Up Double Bass Pedal: A Step-by-Step Guide for Beginners
- How to Set Up Double Bass Pedal with Hi-Hat: A Step-by-Step Guide
- How to Position Double Bass Pedal: Setup Steps for Comfortable Playing
Ready to choose one?
