Where to Place 2nd Crash Cymbal: A Step-by-Step Guide for Drummers
Learn where to place 2nd crash cymbal on your drum kit, with clear reach, angle and spacing tips so you can hit both crashes cleanly without crowding your setup
Updated November 2026
Placing a second crash cymbal is mostly about reach, angle and separation. Put it where your hand or foot can hit it without crossing over the first crash, at a height that matches your stroke, and with enough gap that the two cymbals don’t choke each other. Follow the steps below and you’ll have a second crash that sounds distinct and feels comfortable to play. If you’re still deciding on the first crash, see Where to Place Crash Cymbal on Your Kit: A Step-by-Step Guide for the basics.
Start With Reach and Playing Position
Sit at your throne with your sticks in playing position and note where your arms naturally rest. Your second crash should sit within about one forearm’s length of your strike zone, so you can reach it without leaning or lifting your shoulder. Most drummers put the second crash on the opposite side of the kit from the first, or just outside the hi-hat on the left, depending on whether they are right- or left-handed.
Shopping for one? See our guide: Zildjian 16 Crash Cymbal: 7 Best Picks Compared for Every Drummer.
Set the Height and Angle
Height controls how quickly you can reach the cymbal and how it projects. A good starting point is for the cymbal’s edge to sit roughly level with the top of your snare drum, or slightly above it. Tilt the cymbal so the bell faces slightly toward you, usually at a low angle of about 15 to 30 degrees from horizontal. This keeps the cymbal from sitting flat, which can dampen the sound, and makes it easier to strike the edge with a clean stroke.
Checking the Angle
Strike the cymbal a few times at the bow, about two inches in from the edge, and listen. If the sound is muffled, raise the stand’s height or tilt the cymbal a touch further from you. Adjust in small steps until the tone opens up.
Leave Space Between the Two Crashes
Two crashes placed too close together will choke each other. When one rings, the other’s vibrations can dampen it, and you may accidentally hit both when you only want one. Keep at least 3 to 4 inches of clearance between the edges, and make sure the bells don’t touch when you tilt them. If your kit is cramped, move the second crash slightly outward or raise it a few inches higher on a boom arm.
Checklist Before You Play
- Sit at your throne and confirm both crashes are within easy reach.
- Set the cymbal edges roughly level with or just above the snare top.
- Tilt each crash so the bell angles 15 to 30 degrees toward you.
- Keep at least 3 to 4 inches between the cymbal edges.
- Strike each crash at the bow and listen for clear, unmuffled tone.
- Check that the stands don’t block your hi-hat or toms.
Common Mistakes to Avoid
- Placing the second crash too far back, forcing you to reach over the toms.
- Setting both crashes flat, which dulls the sound and slows the decay.
- Letting the cymbal edges touch, which causes choking and unwanted overtones.
- Ignoring the hi-hat clutch when positioning the stand, leading to clutter.
- Tightening the stand wing nuts before you have the final position set.
Recommended Gear
A sturdy boom stand with a second arm makes it much easier to position a second crash without crowding the kit. Look for one with a stable base and adjustable tilt so you can fine-tune the angle. View on Amazon
Cymbal felts and sleeves protect the cymbal where it sits on the stand and reduce metal-on-metal contact, which helps prevent choking and unwanted buzz. View on Amazon
FAQ
Should the second crash be on the left or right of the kit?
Most drummers place it on the side opposite their dominant hand, so it is reachable without crossing their body. Left-handed players usually reverse this. Choose whatever keeps both crashes comfortable to hit.
How high should a second crash sit?
A common starting point is with the cymbal edge roughly level with or just above your snare drum. Adjust from there based on how quickly you can reach the cymbal and how it sounds.
Can two crashes sit close together?
They can, but keep at least 3 to 4 inches of clearance between edges. Closer placement tends to cause one cymbal to choke the other when both are played.
Conclusion
Place your second crash within easy reach, at roughly snare height and with a slight tilt toward you. Leave a few inches between the two cymbals so each one rings clearly. Make small adjustments while you play, and your second crash will feel like a natural part of your kit.
Related reading
- Where Does the Crash Cymbal Go on Your Drum Kit: A Step-by-Step Guide
- Zildjian K Custom Dark Crash Cymbal Review: Key Features Explained
- Zildjian Crash Ride Cymbal: Which One Fits Your Playing?
- Zildjian Crash Cymbal Pack: How to Choose the Right Set (2026)
- Zildjian 18 ZBT Crash Ride Cymbal: Sound, Fit and Buying Tips
- Zildjian 16 ZBT Crash Cymbal: Sound, Specs and Who It Suits
Ready to choose one?
