Double Bass Pedal Parts: 6 Best Replacement Pieces for Drummers (2026)

Updated November 2026

Double bass pedal parts wear out, snap or go missing, and most drummers reach for a replacement at the worst possible moment: right before a rehearsal or a gig. This guide compares six replacement components for double bass pedal setups, from drive shafts and linkage arms to return springs and cam brackets. Each pick was chosen from its listing details, the type of part it is, and the patterns owners commonly describe, with attention to material, length, fit and whether the part suits single or double pedal hardware.

Our Top Picks

Quick Comparison

Product	Best for	Key feature
TUOREN Double Kick Drum Pedal Drive Shaft	General replacement of a worn drive shaft	Steel linkage connector arm
Colaxi 31cm Steel Double Drum Drive Shaft	Longer spacing between pedal and beater	31cm steel driveshaft rod
Jiayouy Double Bass Drum Foot Pedal Drive Shaft	Drummers replacing a shaft on a tight budget	10mm linkage rod
RANMING Bass Drum Pedal Spring 2Pcs	Replacing one or two broken springs	Carbon steel spring with hook
RANMING 2 Sets Bass Drum Pedal Spring Tension Assembly	Restoring tension across a full pedal	Two complete spring assemblies
TUOREN Bass Drum Foot Pedal Chain Sprocket Cam Bracket	Chain-drive pedals with worn cam or sprocket	Double chain drive connector assembly

TUOREN Double Kick Drum Pedal Drive Shaft Steel Bass Drum Pedal Linkage Connector Arm

Best for: General replacement of a worn or bent drive shaft

This is a good fit for drummers whose drive shaft has bent, loosened or lost its connector and who want a straightforward steel replacement for a standard double pedal linkage.

Key specs

• Steel linkage connector arm for drum kit percussion pedals
• Listed as a double kick drum pedal drive shaft replacement
• Black finish

Pros

• Steel construction suits repeated beater strikes
• Clearly matched to double pedal linkage use
• Simple swap with basic hand tools

Cons

• Fit depends on your pedal’s connector geometry, so measure the old part first
• Listing details are limited on exact dimensions

Bottom line: A sensible first replacement for drummers who need a dependable steel drive shaft and have already confirmed that the part type matches their pedal.

View on Amazon

Colaxi 31cm Steel Double Drum Drive Shaft Pedal Driveshaft Rod

Best for: Longer spacing between pedal and beater

Drummers with a longer drive run, or those rebuilding a DIY setup, may prefer a 31 cm rod that they can cut or fit to their own spacing.

Key specs

• 31 cm steel driveshaft rod
• Designed as a DIY replacement bass drum pedal connector arm
• Black and red finish

Pros

• Length gives flexibility for custom spacing
• Steel rod suits hardware-style pedal builds
• Useful for drummers who like to modify their setup

Cons

• Requires measuring and sometimes trimming to fit
• Not a plug-and-play part for every pedal brand

Bottom line: Best for drummers comfortable with a little measuring who want a long steel shaft they can adapt.

View on Amazon

Jiayouy Double Bass Drum Foot Pedal Drive Shaft for Percussion Instrument Parts

Best for: Drummers replacing a shaft on a tight budget

This option suits players who need a simple, inexpensive replacement linkage rod and are not chasing a specific brand match.

Key specs

• 10mm linkage rod
• Designed for double bass drum foot pedal drive shafts

Pros

• Budget-friendly way to restore a broken shaft
• 10mm diameter is a common size for linkage rods
• Easy to compare against your existing part

Cons

• Diameter and end style must match your pedal exactly
• Fewer listing details than premium brand-name parts

Bottom line: A practical choice for drummers who have confirmed the 10mm size and want an affordable spare.

View on Amazon

RANMING Bass Drum Pedal Spring 2Pcs Standard Replacement Kick Pedal Springs

Best for: Replacing one or two broken springs

If a single spring has snapped or lost tension, a two-piece set lets you fix the problem without rebuilding the whole pedal.

Key specs

• Pack of 2 standard replacement springs
• Carbon steel construction with hook ends
• Listed for single and double drum pedals

Pros

• Carbon steel holds tension well over time
• Hooked ends simplify installation
• Two pieces give a useful spare

Cons

• Spring rate must match your pedal, so check length and hook spacing
• Not suited to replacing a full set of worn springs

Bottom line: Good for drummers who need one or two springs and want to confirm the hook style before ordering.

View on Amazon

RANMING 2 Sets Bass Drum Pedal Spring Tension Assembly Standard Replacement Kick Pedal Springs

Best for: Restoring tension across a full pedal

When a pedal feels uneven or spongy, replacing the whole spring assembly can be quicker than chasing individual problems.

Key specs

• Two spring tension assembly sets
• Carbon steel springs for standard kick pedals
• Suitable for single and double drum pedals

Pros

• Full assembly approach restores even tension
• Two sets cover both pedals in a double setup
• Carbon steel matches the rest of the pedal hardware

Cons

• Requires disassembling the old tension hardware
• Exact fit should be confirmed against your pedal model

Bottom line: A strong option for drummers whose pedals feel worn across the board and who are comfortable doing a fuller rebuild.

View on Amazon

TUOREN Bass Drum Foot Pedal Chain Sprocket Cam Bracket Parts Double Chain Drive Connector

Best for: Chain-drive pedals with worn cam or sprocket

Chain-drive designs rely on the cam, sprocket and bracket working together. If those parts wear, a targeted replacement assembly can restore smooth action.

Key specs

• Chain sprocket and cam bracket assembly
• Double chain drive connector device
• Black finish

Pros

• Targets the most wear-prone parts of a chain drive
• Replaces several components in one assembly
• Useful for drummers who want to avoid a full pedal swap

Cons

• Only relevant if your pedal uses a chain drive
• Installation is more involved than swapping a single rod or spring

Bottom line: Best for drummers with a chain-drive pedal who have confirmed the sprocket and cam are the source of the problem.

View on Amazon

Buying Guide

Identify the drive type first

Before comparing any double bass pedal parts, determine whether your pedal uses a direct drive shaft, a strap or chain drive, or a hybrid design. Shafts and linkage rods only fit shaft-driven designs, while sprockets and cam brackets belong to chain systems. Removing one component and photographing the layout is a reliable way to confirm what you need.

Good picks for this: TUOREN Bass Drum Foot Pedal Chain Sprocket Cam Bracket; TUOREN Double Kick Drum Pedal Drive Shaft

Measure length and diameter

Drive shafts and linkage rods are sold by length and diameter. Measure the old part from connector end to connector end, and note the diameter with a caliper if you have one. A 10mm rod will not seat properly in a pedal built for a different gauge, and a rod that is too long will change your beater angle.

Good picks for this: Colaxi 31cm Steel Double Drum Drive Shaft; Jiayouy Double Bass Drum Foot Pedal Drive Shaft

Match spring tension and hook style

Springs differ in length, wire thickness and hook geometry. Check how many springs your pedal uses, whether they hook at the top or bottom, and how far apart the anchor points sit. Mismatched springs can cause uneven rebound or stress on the baseplate.

Good picks for this: RANMING Bass Drum Pedal Spring 2Pcs; RANMING 2 Sets Bass Drum Pedal Spring Tension Assembly

Consider steel and finish

Carbon steel and steel linkage parts are common in pedal hardware because they resist fatigue under repeated strikes. Finish matters less for function, but a black or matching finish helps replacement parts blend with the rest of the hardware and reduces visible wear.

Good picks for this: TUOREN Double Kick Drum Pedal Drive Shaft; RANMING 2 Sets Bass Drum Pedal Spring Tension Assembly

Think about how much you are replacing

A single snapped spring calls for a different approach than a pedal that feels tired all over. Replacing one or two components is quick and inexpensive, while replacing an assembly or a full set takes more time but restores consistent feel. Decide before ordering so you do not buy too little or too much.

Good picks for this: RANMING Bass Drum Pedal Spring 2Pcs; TUOREN Bass Drum Foot Pedal Chain Sprocket Cam Bracket

Plan for installation

Most shaft and spring swaps need only a screwdriver, a hex key and a few minutes, but chain and sprocket work requires removing tension and realigning the drive. Lay out the old parts in order, take photos during disassembly, and keep fasteners sorted. If you are unsure about a chain-drive rebuild, a drum technician can handle it safely.

Good picks for this: TUOREN Double Kick Drum Pedal Drive Shaft; TUOREN Bass Drum Foot Pedal Chain Sprocket Cam Bracket

Verify compatibility with your pedal brand

Many replacement parts are sold as universal, but pedal geometry varies between manufacturers and generations. Check listing photos, compare against your original part, and look for language about single or double pedal compatibility before buying.

Good picks for this: RANMING Bass Drum Pedal Spring 2Pcs; Colaxi 31cm Steel Double Drum Drive Shaft

FAQ

Can I use a generic drive shaft on any double bass pedal?

Not always. Drive shafts vary in length, diameter and connector style. Measure your original part and compare those dimensions with the listing before ordering.

How do I know if my spring needs replacing?

Signs include uneven rebound, a pedal that feels too loose or too stiff, a visible crack or kink, or a spring that no longer returns the beater fully. Compare it with a matching spring if you have one.

Is a chain-drive part the same as a shaft-drive part?

No. Chain systems use sprockets, cams and chains, while shaft systems use rods and linkage arms. Parts from one system generally will not fit the other.

Do I need to replace both sides of a double pedal?

Not necessarily, but replacing parts in pairs keeps tension and response consistent between the two pedals. If only one side is worn, matching the other side’s spec is important.

Can I install these parts myself?

Many shaft and spring replacements are straightforward DIY jobs with basic tools. Chain and sprocket work is more involved. If you feel unsure, a qualified drum technician can help.

How often should double bass pedal parts be checked?

A quick inspection every few months, or before a major gig, helps catch loose screws, worn springs and cracked connectors early. Heavy playing may call for more frequent checks.

Conclusion

For a general drive shaft replacement, the TUOREN Double Kick Drum Pedal Drive Shaft is a sensible starting point. Drummers who need extra length or want to adapt their setup may prefer the Colaxi 31cm rod, while the Jiayouy part suits a tight budget if the 10mm size is confirmed. For spring problems, the RANMING single-pack suits one or two broken springs, and the two-set assembly fits a full tension refresh. The TUOREN chain sprocket and cam bracket is the choice for chain-drive pedals with worn internal parts. Match the part to the exact component that has failed, and measure before you buy.

Sources

• Guidance on safe handling of tools and hardware during equipment maintenance (osha.gov)
• Consumer safety information on replacing worn or damaged equipment components (cpsc.gov)
• Standards information on steel materials and fastener specifications (nist.gov)

Related reading

• Pearl P532 Double Bass Drum Pedal: Setup, Adjustment and Buying Tips
• Pearl Drum Double Bass Pedal: A Buyer's and Setup Guide
• Left Handed Double Bass Pedal: 5 Best Picks for Lefty Drummers (2026)

About the author