How to Adjust DW 4000 Double Bass Pedal: A Step-by-Step Guide
Learn how to adjust a DW 4000 double bass pedal, from spring tension and footboard angle to beater height and cam setup, for a faster, more even feel.
Updated November 2026
To adjust a DW 4000 double bass pedal, you will set the spring tension, footboard angle, beater height and strap or pedal-to-drum position so the pedal feels responsive without fighting you. Most of the work takes about 15 to 20 minutes. Once it is dialed in, you should be able to play single strokes and double strokes with an even rebound and no wasted motion.
Start with the Pedal Position
Before touching any adjustment knob, position the pedal so your heel rests comfortably on the footboard. The footboard should line up with your foot, and the beater should strike the center of the bass drum head, not the edge. Set the pedal so your heel can sit at a natural height with your knee slightly bent, roughly 20 to 30 degrees, when your foot is on the board. If you are still working out where the pedal sits on the rack, see How to Position Double Bass Pedal: Setup Steps for Comfortable Playing.
Shopping for one? See our guide: 5 Best Electronic Drum Double Bass Pedal Options for Practice and Gigging (2026).
Adjust Spring Tension and Footboard Angle
The DW 4000 series uses an adjustable spring tension system that controls how much resistance your foot pushes against. Tightening the spring makes the pedal feel firmer and return faster, while loosening it gives a lighter, more effortless feel. Make small changes of a quarter turn at a time and play a few bars after each adjustment. The footboard angle is set separately with the angle bolt, which changes the way your heel and toe meet the board. Keep it aligned so your foot stays square over the pedal.
For a broader look at tension, read How to Adjust Double Bass Pedal Tension: 6 Steps for a Faster, Even Feel and How to Adjust Bass Drum Pedal Spring Tension: A Step-by-Step Guide.
Set the Beater Height and Stroke Distance
The beater height determines how far the beater travels before it reaches the head. Set it so the beater rests about 1 to 2 inches from the head when the pedal is at rest. A beater that sits too high will feel slow, and one that sits too close will cause it to hit the head before you have fully pressed down.
- Loosen the beater height adjustment on the pedal’s upper section.
- Raise or lower the beater until it sits at the desired distance from the head.
- Tighten the adjustment and check that the beater lines up with the center of the head.
- Press the footboard slowly to confirm the beater makes full contact and returns cleanly.
Check the Cam and Drive System
The DW 4000 uses a cam to control the way the beater accelerates. The cam setting changes how the pedal feels through the stroke. The default setting suits most players, but you can test a different cam position to change the feel. Keep the chain or strap tension even, and make sure the drive system does not bind. A stiff or uneven drive makes doubles harder to control, so take your time with this step.
Common Mistakes
- Adjusting spring tension in large increments, which makes it hard to tell what changed.
- Setting the beater too close to the head, causing it to bounce or double-strike.
- Ignoring footboard angle, which can cause heel strain or inconsistent strokes.
- Tightening everything at once instead of checking each setting after a change.
- Skipping a final test with your real playing pattern, such as sustained doubles at moderate tempo.
Recommended gear
A few supporting items make pedal setup easier. A hex or Allen key set matches the fasteners on most pedals and prevents stripped bolts during adjustment. A drum key helps fine-tune the bass drum head so the beater impact stays consistent. A practice pad lets you check your pedal feel without disturbing the room.
- Hex key set for tightening angle and height bolts: View on Amazon
- Drum key for adjusting the bass drum head tension: View on Amazon
- Bass drum practice pad for testing pedal feel quietly: View on Amazon
FAQ
How often should I readjust my DW 4000 pedal?
Check the settings every few weeks, or whenever the pedal feels different. Bolts can loosen with regular play, so a quick check keeps the setup stable.
Should I change spring tension if I switch to a heavier beater?
Often yes. A heavier beater adds weight to the stroke, so you may want to increase tension slightly to keep the return fast and controlled.
Is it normal for the pedal to feel stiff after adjustment?
Some stiffness is expected when you first tighten the spring or cam. Play for several minutes before judging the feel, and back off the tension if fatigue sets in.
Conclusion
Adjusting a DW 4000 double bass pedal comes down to a few connected settings: position, spring tension, footboard angle, beater height and cam. Make one change at a time and test each adjustment with real playing. With patience, the pedal will respond the way you want for both single strokes and fast doubles.
Related reading
- How to Adjust a Double Bass Pedal: A Step-by-Step Guide for Drummers
- DW Double Bass Pedal: How to Choose, Set Up and Tune Yours
Ready to choose one?
