We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

How to Attach a Double Bass Pedal: A Step-by-Step Guide for Drummers

Learn how to attach a double bass pedal to your kick drum hoop, check alignment and tension, and get a secure, stable setup in a few clear steps.

Updated November 2026

To attach a double bass pedal, you clamp the pedal’s base plate to the rim of your bass drum hoop, connect the beater to the footboard, and then check that both pedals sit level and secure. The whole process takes most drummers about 15 to 20 minutes with basic hardware. Done right, the pedal stays put under heavy playing and the beater hits the head at a consistent spot.

What You Need Before You Start

Gather these items before you touch the drum. Working on a clear floor with the kick drum lying on its side or sitting on a stable surface makes the job easier.

Shopping for one? See our guide: 5 Best Electronic Drum Double Bass Pedal Options for Practice and Gigging (2026).

  • The double pedal with its footboards, beater assemblies, and any included hardware
  • An Allen wrench set or the specific key the manufacturer supplies
  • A screwdriver for any adjustment screws on the clamp
  • A rubber mat or towel to protect the drum finish
  • A tape measure or ruler for checking the height and spacing

Step-by-Step: Mounting the Pedal to the Hoop

  1. Position the drum. Set the bass drum on its side or on a stand where you can reach the batter head comfortably. Place your mat under it to protect the shell.
  2. Open the clamp. Loosen the clamp bolt so the jaws open wide enough to fit over the hoop without forcing them.
  3. Seat the clamp on the hoop. Slide the clamp onto the rim at the point where your foot naturally falls. Keep the base plate flat against the hoop, not angled.
  4. Tighten the clamp evenly. Snug the bolt until the clamp holds without slipping, then tighten a little more. Avoid cranking it so hard that the hoop dents.
  5. Attach the second pedal’s footboard. Connect the chain or strap to the first beater, then link the second pedal to the drive shaft or coupling as the manufacturer describes.

Aligning the Beaters and Footboards

Once both pedals are on the hoop, the beaters need to strike the head squarely. Misalignment causes uneven doubles and wears the batter head faster.

  1. Sit at the drum throne and place both feet on the footboards in your normal playing position.
  2. Check that each beater meets the head at the same height and angle. The beater face should sit roughly perpendicular to the head.
  3. Adjust the beater height so the striking surface is close to the head at rest, typically a few millimeters above it.
  4. Confirm that the footboards line up with your heels and that neither pedal pulls the other out of place when you press down.

Setting the Spacing Between Pedals

Most drummers place the two footboards side by side with a small gap. Measure the distance between the footboard centers and keep it consistent with your natural stance. If your feet feel cramped, shift the second pedal’s clamp along the hoop rather than forcing the drive shaft to bend.

Checking Stability and Tension

A pedal that moves during a fast passage distracts you and can damage the drum. Test the setup before you play for real.

  • Press each footboard firmly and listen for any creaking or shifting at the clamp.
  • Play a slow pattern, then a fast one, and watch whether the pedal walks along the hoop.
  • Recheck the clamp bolts after the first session, since new hardware often settles.

A few accessories make a clamped double pedal easier to set and keep steady.

  • Drum key: A sturdy tuning and hardware key with a comfortable grip makes tightening clamp bolts less fiddly. View on Amazon
  • Anti-slip pedal mat: A rubber mat under the pedal base helps resist movement on the floor. View on Amazon
  • Drum rug: A large rug under the kit keeps the pedal base from skating during heavy playing. View on Amazon

Common Mistakes to Avoid

  • Overtightening the clamp, which can dent the hoop or crack the finish.
  • Mounting the pedal at an angle, which causes the beater to strike off center.
  • Skipping the post-setup stability test and discovering creep only mid-song.
  • Leaving the drum unsupported while you work, which risks scratching the shell.

For more on dialing in the feel once everything is attached, see How to Set Up Double Bass Pedal: A Step-by-Step Guide for Beginners and How to Position Double Bass Pedal: Setup Steps for Comfortable Playing. If the pedal starts drifting after installation, How to Stop Double Bass Pedal from Moving: 6 Fixes That Work covers the most common causes.

FAQ

Can I attach a double bass pedal to any kick drum?

Most double pedals use a standard hoop clamp that fits common bass drum sizes, but check the manufacturer’s listed compatibility. Very thin or unusual hoops may need a different clamp.

Do I need to remove the batter head to attach the pedal?

No. The pedal clamps to the outside of the hoop, so the head can stay in place.

How tight should the clamp be?

Tighten it until the pedal no longer slides under playing pressure, then stop. If you see the hoop bending or the finish marking, you have gone too far.

Conclusion

Attaching a double bass pedal comes down to a secure clamp, aligned beaters, and a quick stability check. Take your time on the alignment step, since it shapes how every double sounds and feels. Once the setup is solid, you can focus on your playing instead of your hardware.

Audrey Hayes

About Audrey Hayes

Audrey Hayes is part of our editorial team and reviews and edits our drums guides, checking product details against manufacturer specifications and owner feedback.

About the author

Audrey Hayes
Audrey Hayes

Audrey Hayes writes reviews and buying guides for Drum Path.