We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

How to Make a Cymbal Display Stand: A Step-by-Step Guide for Beginners

Learn how to make a cymbal display stand at home with basic tools, simple measurements and a stable base. A practical guide for drummers who want to show off th

Updated November 2026

Learning how to make a cymbal display stand gives you a sturdy, good-looking way to show off a cymbal without tying up your kit. You will build a freestanding base, a vertical post and a cradle that holds the cymbal edge-up at a safe angle. The whole project takes a few hours and uses materials most home workshops already have.

Plan the Size and Load Before You Cut

Start by measuring the cymbal you plan to display. Most crash and ride cymbals fall between 16 and 22 inches, so your cradle should be at least two inches wider than the bell on each side. Decide how high you want the cymbal to sit. A display height of 14 to 18 inches from the base works well for a shelf or desk, while a floor-level display can reach about 30 inches.

Shopping for one? See our guide: Top 5 Hi-Hat Cymbal and Stand Picks for Every Drummer (2026).

Keep the base heavy enough to resist tipping. A base footprint of roughly 10 by 10 inches with a dense hardwood or a weighted bottom keeps a single cymbal steady even if someone bumps the table.

Build the Base and Post

Cut a square base from 3/4-inch plywood or hardwood. Drill a centered hole for the post, sized to fit a 3/4-inch dowel or a short length of threaded rod. Glue and screw a second layer underneath or add a flat weight, such as a metal plate, to lower the center of gravity.

Mount the post upright in the hole with wood glue and a couple of cross screws. Check with a level from two directions. If the post leans even slightly, the cymbal will sit crooked and may slide.

Make the Cymbal Cradle

The cradle holds the cymbal by its edge, so it must not touch the bell or the playing surface. Cut a 2-inch-wide crosspiece from hardwood and attach it to the top of the post at a slight angle, roughly 10 to 15 degrees from horizontal. Add two small arms or a shallow U-shaped channel so the cymbal rests on its bow, not its bell.

Line every contact point with felt, cork or thin rubber. This protects the finish and prevents metal-on-wood rattle. A small rubber washer on the post helps the cymbal sit flat and quiet.

Finish and Test

Sand all surfaces smooth, starting around 120 grit and finishing at 220. Apply a clear finish or paint, then let it cure fully before mounting a cymbal. Set the cymbal on the cradle and tap it gently to confirm it sits still. Adjust the arms or padding until the fit is snug without pressure on the bell.

Quick Build Checklist

  1. Measure the cymbal diameter and bell depth.
  2. Cut a base at least 10 by 10 inches.
  3. Drill and set a centered post.
  4. Check the post with a level.
  5. Attach the angled cradle with padding.
  6. Sand, finish and let cure.
  7. Test the fit with a gentle tap.

Common Mistakes

  • Making the base too light, which invites tipping.
  • Letting the cradle touch the bell instead of the edge.
  • Skipping padding, which causes rattle and scratches.
  • Setting the cymbal at too steep an angle, which lets it slide.
  • Mounting a cymbal before the finish fully cures.

A reliable drill and a set of spade or Forstner bits make the centered post hole much cleaner. View on Amazon

Self-adhesive felt pads protect the cradle contact points and reduce rattle against the cymbal edge. View on Amazon

A small torpedo level helps you confirm the post is plumb before the glue sets. View on Amazon

If you want a ready-made option or a deeper look at stand design, see How to Make a Cymbal Stand: A Step-by-Step Guide for Beginners and Splash Cymbal and Stand: A Step-by-Step Guide to Choosing the Right Setup.

FAQ

Can I use a cymbal stand instead of building one?

Yes. A standard cymbal stand works for display if you add a felt pad under the clutch and set the cymbal at a low angle. Keep it away from foot traffic.

What wood works best for a cymbal display base?

Hardwood or 3/4-inch plywood are the most common choices because they are dense and hold screws well. Avoid soft pine for the base.

Is it safe to display a cymbal on a shelf?

It is safe when the base is heavy, the cradle is padded and the cymbal is secured. Keep it out of reach of children and pets, and consult a professional woodworker if you plan a large or wall-mounted display.

Conclusion

A well-built display stand protects your cymbal and turns it into a clean, visible part of your room. Measure carefully, build a heavy base, and pad every contact point. With those three steps, your cymbal will sit securely for years.

Audrey Hayes

About Audrey Hayes

Audrey Hayes is part of our editorial team and reviews and edits our drums guides, checking product details against manufacturer specifications and owner feedback.

About the author

Audrey Hayes
Audrey Hayes

Audrey Hayes writes reviews and buying guides for Drum Path.